well duh - Server not found

Did you install virtualmin through the install.sh ? do you see /home/tomjerry and does it contain the necessary files and folders like public_html ?
Did you use virtualmin to create the domain tomjerry ?

What's in the Apache logs? First thing to check in case of problems with Linux stuff is always the logs.

I think your problem is the manual installation of virtualmin.
Virtualmin normally installs suexec which looks like you dont have.
What you can try is remove apache and then install it again but make sure you have the virtualmin repositories in /etc/yum.repos.d
it is a file called virtualmin.repo and the contents for a centos 6.2 server is

[virtualmin]
name=RHEL/CentOS/Scientific $releasever - $basearch - Virtualmin
baseurl=http://SERIALNUMBER:LICENSEKEY@software.virtualmin.com/gpl/rhel/$releasever/$basearch/
enabled=1
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-virtualmin
gpgcheck=1
 
[virtualmin-universal]
name=Virtualmin Distribution Neutral Packages
baseurl=http://SERIALNUMBER:LICENSEKEY@software.virtualmin.com/gpl/universal/
enabled=1
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-virtualmin
gpgcheck=1

edit:
It could be that apache was compiled with suexec and that you need to load the module only in the httpd.conf
LoadModule suexec_module modules/mod_suexec.so
If not you will need a new apache compiled with suexec and that is described above.

Howdy,

The problems you're having do appear to be related to your manual install, the automated installer sets that all up for you.

But, a clean install in order to use that automated installer implies formatting, and reinstalling your operating system.

You can continue with a manual install of Virtualmin, though doing may be some work :-)

There are instructions for doing a manual install here, you may wish to review the instructions:

http://www.virtualmin.com/documentation/installation/manual

I'd also recommend disabling any software repositories outside of the CentOS and Virtualmin repositories, as those would just further complicate things :-)

You may also want to comment out the "NameVirtualHost *" entry in your httpd.conf, as you only need the "NameVirtualHost 192.168.1.5:80" entry.

I'd also suggest grabbing the version of Apache provided by Virtualmin, as Ronald had mentioned.

-Eric

Howdy,

Well, unfortunately, it's really not possible to do a "clean" install without formatting and starting over.

Non-standard packages and config file changes can cause problems with your Virtualmin installation. And the RPMForge repository is known to contain packages that conflict with those provided by Virtualmin.

Now, you can of course try a Virtualmin install using the install.sh without formatting, but I'd expect to have to do some troubleshooting and extra work that wouldn't occur when working with a freshly installed distro.

Since RPMforge has packages that conflict with Virtualmin -- my recommendation would be to configure that repository to only pull down the packages you need, rather than allowing all packages to be installed.

It sounds like you took some good first steps though, by removing packages that would be likely to be troublesome... my suggestion would be to completely disable the RPMForge and EPEL repositories during the Virtualmin installation, and then afterwards, re-enable them and configure them to just pull down the packages you need from those repos by specifying your desired packages in the "includepkgs=" option in the .repo file.

-Eric

for the NAT thing you can go to virtualmin - System Settings - Virtualmin Configuration - Networking Settings.
Default virtual server IP address: would be your internal address
Default IP address for DNS records Would be your external address

Is apache now compiled with suexec /home ?
Do you see the suexec group in the httpd.conf - virtualhost container?
Below is an example

<VirtualHost xx.xx.xx.xx:80>
SuexecUserGroup "#747" "#632"
ServerName domain.info
DocumentRoot /home/domain.info/public_html
ErrorLog /home/domain.info/logs/error_log
CustomLog /home/domain.info/logs/access_log combined
ScriptAlias /cgi-bin/ /home/domain.info/cgi-bin/
ScriptAlias /awstats/ /home/domain.info/cgi-bin/
DirectoryIndex index.html index.htm index.php index.php4 index.php5
<Directory /home/domain.info/public_html>
Options Indexes IncludesNOEXEC FollowSymLinks +ExecCGI
allow from all
AllowOverride All
AddHandler fcgid-script .php
AddHandler fcgid-script .php5
FCGIWrapper /home/domain.info/fcgi-bin/php5.fcgi .php
FCGIWrapper /home/domain.info/fcgi-bin/php5.fcgi .php5
</Directory>
<Directory /home/domain.info/cgi-bin>
allow from all
</Directory>
RemoveHandler .php
RemoveHandler .php5
</VirtualHost>

so if you open a shell and type: httpd -V
you can see if your apache is compiled with suexec and thus coming from virtualmin repo
if that is the case you could try to go to Virtualmin - Server Configuration - Website Options and set PHP script execution mode to FCGId (run as virtual server owner)

Otherwise i think you still have the incorrect apache thus not from virtualmin repo